Power T-Display-S3 with a external 3.3V (preferred) or 5V source

[danielcharrua]

Hello,

I need to power the board with a regulated external 3.3V (preferred) or 5V source:

In case of 3.3V:

• Is ok to connect it trough 3V PIN and GND?

In case of 5V:

• Is ok to connect it trough 5V PIN and GND?

In any case:

• Sometimes a USB (PC) connection must be made to upload firmware, what happens when the two power sources are connected at the same time? If this is bad, using a Schottky diode on the external power source can solve this issue? I need to be sure that both devices are safe (board, external power source and PC)
• Does the T-Display-S3 include any protection on the USB side for backfeed and protect the PC?

I'm sorry if my technical language here is not adequate, I'm no expert.

I have also read that when using external power some pins must be changed @teastainGit

Thanks. All help is much appreciated.

[teastainGit]

Hi! teastainGIT here.
Due to the sophisticated power section of the LilyGO T-Display S3 the power incoming has to be 5V USB (4.2V may work) and 3V to 6V coming into the battery charge connector (below and facing backward of the USB-C).
USB 5V is available on one external pin as an output only to supply some sensors with 5V, but cannot be used to backfeed 5V to the board.

No pins must be changed when using external power. Two very important GPIOs must be set HIGH in order for the display to work.
From my repository :

 #define PIN_POWER_ON 15  // LCD and battery Power Enable
  #define PIN_LCD_BL 38    // BackLight enable pin (see Dimming.txt)

just before the setup and then in setup add:
  pinMode(PIN_POWER_ON, OUTPUT);  //triggers the LCD backlight
  pinMode(PIN_LCD_BL, OUTPUT);    // BackLight enable pin
  
  digitalWrite(PIN_POWER_ON, HIGH);
  digitalWrite(PIN_LCD_BL, HIGH);

With the charging connector you can plug and unplug USB-C at random!
Hope this helps!
-Terry

[danielcharrua]

Hey @teastainGit thank you for the response.

Correct me if I understand wrong: I can feed from 3V to 6V from an external power source into the battery charge connector?

And also I can plug the USB-C and load firmware? No need for diodes or any extra protection? No backfeeds or damaging USB-C port on the PC or the external power source?

Thank you again.

[teastainGit]

You are correct.
The reason for the complicated design is to allow 5V from the USB to be fed to an IC battery charge controller chip and charge up the battery. I use a 5V white iPhone charger to power it, or 3 AA cells through the 2pin charge connector.
You can plug it into a computer USB and program it while charging off the USB!
Do not exceed 6V on either connector.
Trying to connect 5V through the 5V pin on the board has resulted in reports of damage and/or faulty running. It is intended to power older 5V sensors from the Arduino days. It DOES backfeed with potential damage and upset some users.
The two outputs that I mention must be set HIGH with every sketch, even some cool app for ESP32 downloaded from somewhere on The Internet!
I am just an experienced user, not with LilyGO, but I had tremendous problems with this board...so I made a GitHub repository.
-cheers

[danielcharrua]

Hey @teastainGit,

So the recommendations are not to power directly the board from the 5V or 3V pins because of faulty running and backfeed to the USB-C.

The something I think I have different than yours and is that my external source power is not a battery but another device. This is a coffee machine with a 3.3V regulator.

I was thinking on powering the T-Display-S3 with this external device but if I connect the external power supply onto the battery port and also connect the USB-C I think I'll get backfeed to the coffee machine. So that's why I was thinking on using a Schottky diode.

My original idea was to power directly from the 3V or 5V pin with this diode protecting the external power source.

Agggh I'm lost here. It would be great that the board includes a secure option to power from an external 5V source and is protected on both sides for backfeed.

Thank you.

[lewisxhe]

I think you can use the 5V pin to input 5V, which is the same line as the USB 5V.

[danielcharrua]

I thought so, but need to be sure if I can power the T-Display-S3 from that pin with no damage. Also need to be sure if the USB-C is connected and also powered with the 5V pin, no damage or backfeed to the PC or the external power source.

[lewisxhe]

You can see from the schematic diagram that 5V = USB 5V. If the voltage is normal, then it has the same effect as connecting to USB.

[danielcharrua]

@lewisxhe ok! And if both power sources are connected? (5V through pin and USB-C) can exist any damage on any of the devices? I need to limit this with a diode? Is already protected by design on the board?

Thanks.

[lewisxhe]

They are the same line without any isolation. It is best not to connect them at the same time.

[danielcharrua]

Hi @lewisxhe, great information.

Is there a way to have both power supplies at the same time? I need to use the board with a power source always connected from 3V or 5V and sometimes connected to USB to update firmware. Do you have some information on isolating and having no issues? Any data is welcomed for me to investigate.

Thank you.

[lewisxhe]

Do you need to use the 3.3V external power supply of Display S3? At the same time, it is necessary to use external 5V Pin power supply, and then maintain the connection of Usbc for updating the sketch, right?

[danielcharrua]

@lewisxhe Maybe I did not explain myself as good as I wanted... I'm installing the Display S3 into a coffee machine, and need to power the Display S3 with power gathered from the coffee machine main board (I think I can get 5V or 3.3V somewhere).

The Display S3 will also need to be connected to the USBC sometimes for some updates, so in that time, the Display S3 will be sourced with two power lines, the one coming from the coffee machine board and the USBC. I wanted to create some sort of protection and be safe with all devices.

[lewisxhe]

Do you need to provide 3.3V or 5V from the coffee machine to provide power to DisplayS3?
You can directly connect 5V from the coffee machine to the 5V Pin on DISPLAY S3, and then cut off the VBUS 5V on the USBC line, so that you can update via USB and use 5V power supply at the same time

[danielcharrua]

When you say "cut the VBUS 5V on the USBC line" do you mean to cut the +5V cable on the USB cable or to cut the trace on the circuit?